Tower Crane Safety Devices Explained: Load Moment Limiter, Anemometer and Anti-Collision

Nov 18, 2026

Leave a message

Quick Answer: The Four Safety Device Families

Every tower crane carries four device families: load and moment limiting, motion limiting, wind monitoring and collision and zone protection. The load moment limiter is the one that prevents structural failure; the others prevent specific accident patterns. All four are required by ISO 10245-1, EN 12077-2 and, in China, GB 5144 and JGJ 332-2014.

 

Family

Core device

What it prevents

Typical specification

Load limiting

Load moment limiter (LML)

Overload and structural collapse

Cut-off at 90% and 110% of rated moment, accuracy +/-5%

Motion limiting

Hoist, trolley and slewing limiters

Hook over-run, trolley over-travel, uncontrolled slewing

Two-stage: slow-down then stop, with mechanical back-up

Wind monitoring

Anemometer at jib height

Lifting above the wind limit

Alarm at 10 m/s, lifting suspended at 12 m/s

Collision protection

Anti-collision and zone system

Crane-to-crane and crane-to-structure contact

Position accuracy 0.3 to 1 m, response under 1 second

 

 

Why This Is a Commercial Question, Not Only an Engineering One

Safety devices are usually discussed as a compliance topic. For a buyer, they are a commercial topic with three cost centres attached.

The first is insurance. Most crane insurers require documented functioning of the load moment limiter and the anemometer, and a claim after an incident is where a missing calibration record becomes a financial event rather than a paperwork gap.

The second is downtime. A limiter that trips spuriously stops the crane, and operators respond to spurious trips by bypassing the device, which converts a reliability problem into a safety problem within a week.

The third is resale and certification. A machine with an uncalibrated or missing limiter cannot pass a third-party inspection in most markets, which removes the regulated segment of the buyer pool from the resale market.

 

 

The Safety Chain: Four Layers, Four Failure Modes

Tower crane protection is not a single system. It is a chain of four layers, and each layer fails in its own way. Understanding the layers explains why a machine can be compliant on paper and unsafe in practice.

Layer one: mechanical. The rated load chart, the structural design margin, the rope safety factor. This layer does not fail suddenly; it degrades through fatigue and corrosion.

Layer two: electrical and hydraulic. Limit switches, brakes, emergency stop. These are the devices that physically stop motion, and they are the layer most affected by moisture, vibration and poor maintenance.

Layer three: electronic. Load moment limiter, anemometer, anti-collision, data logger. Accurate and adjustable, which is also why they get adjusted out of function.

Layer four: management. The permit system, the lift plan, the operator's authority to refuse a lift. This is the only layer that can stop a lift when all three others have been defeated.

 

 

The Load Moment Limiter: The Device That Prevents Collapse

The load moment limiter measures two inputs continuously: the load on the hoist rope and the trolley position. Multiplying them gives the actual load moment, which is compared against the rated curve for the jib length in use.

The comparison is not a single number. The limiter holds a curve, because rated capacity falls as the trolley moves outward. A 6015 lifts 8 t at 15 m but only 1.5 t at 60 m, and the limiter has to know the whole curve, not one point.

A working limiter does three things in sequence. It displays the actual and rated values so the operator can plan the lift. It gives a pre-warning, typically at 90 percent of rated moment, so the operator can retract before the stop. It cuts the hoisting-up and trolley-out motions at 100 to 110 percent, while always allowing the reverse motions so a suspended load can be recovered.

That last detail matters more than it appears. A limiter that blocks all motions on overload traps a suspended load in the air. Any competent design permits hoist-down and trolley-in under overload conditions.

 

Parameter

Typical setting

Why this value

Consequence of error

Pre-warning

90% of rated moment

Gives reaction time before cut-off

Too early: operators ignore it

Cut-off

100 - 110% of rated moment

Allows for dynamic effects

Too high: structural overload permitted

Accuracy

+/-5% of indicated value

Achievable with strain or pressure sensing

Drift makes the display untrustworthy

Recovery motion

Hoist-down and trolley-in always enabled

Prevents a trapped load

Blocking all motions creates a new hazard

Calibration interval

12 months, and after any rope or sensor change

Sensor drift and rope stretch

Uncalibrated unit reads low and never trips

 

 

Motion Limiters: The Three That Fail Most Often

Motion limiters are simple devices, which is why their failures are so common: they are mechanical, exposed and cheap to ignore.

Limiter

Function

Two-stage behaviour

Common failure

Hoist height limiter

Prevents hook block contacting the jib

Slow-down at the pre-limit, stop at the final limit

Weights removed or tied up after a nuisance trip

Trolley limit

Prevents trolley over-travel at jib tip and root

Slow-down then stop, with buffer

Switch arm bent by impact, contacts welded

Slewing limit

Restricts rotation where the site requires it

Slow-down then stop, both directions

Set too wide to be useful, or disabled on sites with no boundary

The hoist height limiter deserves a specific warning. Its final limit is the last protection against two-blocking, where the hook block contacts the trolley and the rope continues to pull. Two-blocking damages the rope, the sheaves and sometimes the jib, and it happens most often with an inexperienced operator on a rapid hoist cycle.

 

 

Tower Crane Anemometers: The Device Most Often Mounted Wrong

Wind is the load that tower crane design spends the most effort on, and the anemometer is the sensor that turns design margin into an operational decision. Two things determine whether it works: mounting position and the link to action.

Mount the anemometer at the top of the tower or on the jib, clear of the slewing structure's wind shadow. A sensor mounted on the cabin or inside the tower reads a fraction of the true wind at jib height, and a sensor that reads low is worse than no sensor, because it is trusted.

Wind speed

Typical site action

Basis

10 m/s

Alarm, operator reviews the lift

Start of the caution band

12 m/s

Suspend lifting of large panels and long loads

Sail area and dynamic response

15 m/s

Suspend all lifting, lower the hook, release slewing brake

Loss of load control

Above 20 m/s

Secure the machine, evacuate the jib area, follow storm procedure

Park position per manual

 

These figures are typical site rules, not universal law. The governing values are in the manufacturer's manual for the specific model, and they change with jib length and panel size. A 60 m jib crane and a 75 m jib crane do not park at the same wind speed.

The operational detail that decides whether the anemometer matters is the parking procedure. In high wind the crane must be left in the free-slew condition with the brake released, so the jib weathervanes. A crane left with the slewing brake applied in a storm takes the full wind moment into the tower.

 

 

Tower Crane Anti-Collision and Zone Protection

Single-crane safety is a solved problem. Multi-crane safety is not, and it is where the accidents on dense sites happen. Anti-collision systems address three distinct risks.

Crane-to-crane collision. Two or more cranes with overlapping slewing circles. The system tracks each crane's position, jib angle and trolley position, predicts intersection and slows or stops one machine before contact.

Crane-to-structure contact. The jib or counter-jib approaching a building, a tower or an overhead line. This is handled by zone limitation rather than by tracking another crane.

Restricted airspace. Schools, railways, highways, airports and residential neighbours. Zones are defined as planes, cylinders or height ceilings, and the system prevents the jib or load from entering.

Position accuracy of 0.3 to 1 m is normal for radio-based systems, and it is adequate because the system stops the crane at a slower speed before the boundary, not at the boundary itself. A system claiming centimetre accuracy by radio is describing a specification it cannot meet in a steel environment.

Installation quality decides performance more than the brand does. Antenna placement, cable routing and the calibration of the zero position are the three points where installations fail.

 

 

The Data Logger and Why Regulators Ask for It

Modern tower cranes carry a monitoring unit that records load, moment, radius, wind speed, slewing angle and alarm events. In China, JGJ 332-2014 sets out the requirement for a tower crane safety monitoring system, including the parameters to be recorded and the display expected in the cabin.

The commercial value of the logger is not compliance. It is evidence. After an incident, the record shows whether the limiter was functioning, what the load was, and what the wind was doing in the ten minutes before. After a dispute with a client about a lift, it shows the same thing.

Recorded parameter

Typical interval

Why it is kept

Load and moment

1 to 5 seconds

Reconstructs the lift and the overload history

Radius and height

1 to 5 seconds

Shows the path of the load

Wind speed

1 to 5 seconds

Establishes conditions at the time

Alarm and cut-off events

Event-driven

Proves whether devices operated

Operator identity

Per shift

Ties the record to a person

 

 

Inspection and Calibration Schedule

Devices fail quietly. The schedule below is the minimum that keeps them honest, and it is the schedule a third-party inspector will expect to see documented.

Interval

Task

Who

Record

Daily, before use

Visual check of limiter display, anemometer reading, limit switch function

Operator

Daily checklist

Weekly

Test hoist height and trolley limits at slow speed

Operator or technician

Log entry

Monthly

Verify LML pre-warning and cut-off with a known load

Technician

Test sheet with values

Quarterly

Anti-collision zone test, anemometer comparison with a handheld unit

Technician

Zone test report

Annually

Full calibration of LML and anemometer, brake test, load test

Certified inspector

Calibration certificate

After any change

Recalibration following rope, sensor or reeving change

Technician

Amendment to the certificate

 

Send Inquiry
Send Inquiry